If using the model’s 3D edges for a 2D Contour is unsuccessful due to complexity, which choice below is a good alternate technique?

(Select one)

Projecting the edges to a 2D sketch and selecting the contour as the geometry to be machined
Create 3D sketch geometry based on the model’s edges
The geometry must be deleted and simplified before proceeding
Copy the model’s faces and paste them as individual surfaces

Select an answer

When setting tool orientation in a toolpath, what additional option must sometimes be used to control the direction the tool will approach the selected geometry from?

(Select one)

Rest Machining
Flip Axis
Tabs
Stock Contours

Select an answer

Which two choices are available to you when using the Derive command?

Select up to undefined

Insert into assembly
Create New Design
Break Link
Add to Existing Design

Select an answer

One major disadvantage of including multiple faces in the same Multi-Axis Flow toolpath is that:

(Select one)

The same Isometric Direction will be used for all of the surfaces
Feedrates will be limited to a maximum value
The same number of stepovers will be used to cut each of the faces that may differ in size, resulting in stepover distances that might not be acceptable
The included faces can only be cut using 3-axis movements

Select an answer

Which two of the following choices can influence the resulting surface finish quality on the machined part when using the Multi-Axis Flow toolpath?

Select up to 2

Smoothing
Retraction Policy
Tolerance
Stock to Leave

Select an answer

Where is the Probe command accessed?

(Select one)

In the Multi-Axis dropdown menu
In the Setup dropdown menu
In the Manage dropdown menu
In the Inspect dropdown menu

Select an answer

In order to drill a hole that has an axis which is not parallel to the current Z axis, you must also choose which of the following when configuring the Drill toolpath?

(Select one)

Tool Number
Chip Breaking cycle type
Drill Tip Through Bottom
Tool Orientation

Select an answer

Which parameter in the Multi-axis Flow toolpath indirectly controls the spacing between passes that the tool makes?

(Select one)

Cutting mode
Number of Stepovers
Direction
Tolerance

Select an answer

When defining stock in a new Setup, Fusion 360 creates default stock dimensions that are:

(Select one)

Based only on the size of any fixturing that has been modeled
Based only on a single component
Dependent on the file size
Large enough to enclose all of the bodies and components in the design

Select an answer

Where can the Manual NC command be found?

(Select one)

In the Actions dropdown menu
In the Setup dropdown menu
In the 2D dropdown menu
In the Multi-Axis dropdown menu

Select an answer

Which direct modeling tool behaves differently depending on whether you’re in the solid tool set or surface tool set

(Select one)

Delete
Press Pull
Replace Face
Move/Copy

Select an answer

Although 2D Contour toolpaths can be applied to 3D selections or non-planar model geometry selections, it is especially important to keep which one of the following items in mind?

(Select one)

The size of the file
Whether it is a Milling setup or a Turning or Mill/turn setup
Whether the design contains more than one component
The offset direction of the tool

Select an answer

When creating a single setup sheet based on multiple setups, which limitation needs to be kept in mind?

(Select one)

Only tool numbers and operation names will be included
The resulting setup sheet cannot be saved
The setup sheet is stored in the cloud and cannot be accessed without a network connection
A single preview image for only one of the setups will be included

Select an answer

When selecting part edges for 2D Contour toolpath geometry, which of the following can influence how Fusion 360 highlights valid selection choices?

(Select one)

The size of the part
The part’s complexity
The tool orientation direction
How the part is clamped

Select an answer

In situations where there aren’t finished surfaces or edges on the part or the fixture, it can be useful to machine a feature in a known location (such as a counterbore) on one of the fixture components in order to:

(Select one)

Make a practice cut
Check a tool’s length offset
Use it to establish the setup’s coordinate system
Test the quality of the coolant mixture

Select an answer

Which of the following options is the best choice for defining irregularly shaped stock based on a body or component which has been modeled in your design?

(Select one)

From solid
Relative size cylinder
Relative size box
Fixed size box

Select an answer

If a Swarf toolpath’s Drive Mode is set to Contours, which is not a Selection Mode option?

(Select one)

Manual
Faces
Splines
Contour pairs

Select an answer

Which Multi-axis Flow toolpath parameter allows you to change the directionality of the passes along the selected geometry?

(Select one)

Tangential Fragment
Smoothing
Isometric Direction
Direction

Select an answer

When defining a tool’s parameters in the tool library, it is especially important to be sure that:

(Select one)

The parameter values you use match the actual physical tool’s dimensions
They are slightly larger than the physical tool’s dimensions
They are based on tools found in the sample libraries included with Fusion 360
You save the file first

Select an answer

Which parameter in the Multi-Axis Contour toolpath forces the tool to move a specified distance past the start point?

(Select one)

Pass Overlap
Sideways Tilt
Forward Tilt

Select an answer

Fusion 360 checks against which two choices below when the Stop on Collision option is enabled during toolpath simulation?

Select up to undefined

The stock that has been defined
The model that has been selected to be machined in the setup
Bodies that have been selected as a fixture
All bodies that are in the design

Select an answer

In order to post process more than one CAM Setup at the same time, it is necessary to make sure that which parameter value is different for each setup?

(Select one)

Program Comment
WCS Offset
Stock Offset Mode
Program Name/Number

Select an answer

While defining the setup, it’s possible to select a body or component to be used as which of the following two choices below?

Select up to undefined

Fastener
Vise jaw
A fixture
Model to be machined

Select an answer

Which simpler option below can sometimes be a good alternative to a simultaneous Multi-Axis Contour toolpath?

(Select one)

Multi-axis positioning 2D Contour toolpath
Swarf Toolpath
Flow Toolpath
Drill Toolpath

Select an answer

One important advantage of creating a distributed design is:

(Select one)

Being able to work in offline mode
Bringing in geometry from other designs to be re-used for creating new features
Shortening the time it takes to open a file
Minimizing the number of files

Select an answer

The 2D Adaptive Clearing toolpath’s major advantage over the 2D Pocket toolpath is that:

(Select one)

Fewer burrs on edges
The chipload is consistently maintained
The resulting surface finish is smoother
Smaller overall file size

Select an answer

Before a tool can be created and stored in the cloud, which of the following must you do first?

(Select one)

Save the file you’re working with
Switch to the Design workspace
Enable Cloud Libraries in user preferences
Close and re-open Fusion 360

Select an answer

Which parameter can be decreased to reduce the calculation time for a Multi-Axis Flow toolpath to make exploring toolpath options easier?

(Select one)

Stock to Leave
Use Multi-Axis
Number of Stepovers
Tangential Fragment

Select an answer

Where is the New Folder command located in the Manufacture workspace?

(Select one)

In the Manage dropdown menu
In the Multi-Axis dropdown menu
In the Setup dropdown menu
In the Inspect dropdown menu

Select an answer

What length is the preferred amount of a tool’s projection from the holder?

(Select one)

2 times the flute length
No less than 1 inch
10 times the diameter of the tool
The least amount possible

Select an answer

Start your final test

Final test

If using the model’s 3D edges for a 2D Contour is unsuccessful due to complexity, which choice below is a good alternate technique?

When setting tool orientation in a toolpath, what additional option must sometimes be used to control the direction the tool will approach the selected geometry from?

Which two choices are available to you when using the Derive command?

One major disadvantage of including multiple faces in the same Multi-Axis Flow toolpath is that:

Which two of the following choices can influence the resulting surface finish quality on the machined part when using the Multi-Axis Flow toolpath?

Where is the Probe command accessed?

In order to drill a hole that has an axis which is not parallel to the current Z axis, you must also choose which of the following when configuring the Drill toolpath?

Which parameter in the Multi-axis Flow toolpath indirectly controls the spacing between passes that the tool makes?

When defining stock in a new Setup, Fusion 360 creates default stock dimensions that are:

Where can the Manual NC command be found?

Which direct modeling tool behaves differently depending on whether you’re in the solid tool set or surface tool set

Although 2D Contour toolpaths can be applied to 3D selections or non-planar model geometry selections, it is especially important to keep which one of the following items in mind?

When creating a single setup sheet based on multiple setups, which limitation needs to be kept in mind?

When selecting part edges for 2D Contour toolpath geometry, which of the following can influence how Fusion 360 highlights valid selection choices?

In situations where there aren’t finished surfaces or edges on the part or the fixture, it can be useful to machine a feature in a known location (such as a counterbore) on one of the fixture components in order to:

Which of the following options is the best choice for defining irregularly shaped stock based on a body or component which has been modeled in your design?

If a Swarf toolpath’s Drive Mode is set to Contours, which is not a Selection Mode option?

Which Multi-axis Flow toolpath parameter allows you to change the directionality of the passes along the selected geometry?

When defining a tool’s parameters in the tool library, it is especially important to be sure that:

Which parameter in the Multi-Axis Contour toolpath forces the tool to move a specified distance past the start point?

Fusion 360 checks against which two choices below when the Stop on Collision option is enabled during toolpath simulation?

In order to post process more than one CAM Setup at the same time, it is necessary to make sure that which parameter value is different for each setup?

While defining the setup, it’s possible to select a body or component to be used as which of the following two choices below?

Which simpler option below can sometimes be a good alternative to a simultaneous Multi-Axis Contour toolpath?

One important advantage of creating a distributed design is:

The 2D Adaptive Clearing toolpath’s major advantage over the 2D Pocket toolpath is that:

Before a tool can be created and stored in the cloud, which of the following must you do first?

Which parameter can be decreased to reduce the calculation time for a Multi-Axis Flow toolpath to make exploring toolpath options easier?

Where is the New Folder command located in the Manufacture workspace?

What length is the preferred amount of a tool’s projection from the holder?