If a toolpath preview has a lot of rapid movements above the part, which toolpath setting is likely to reduce that?

(Select one)

Maximum Stay-Down Distance.
High Feedrate Mode.
Entry Positions.
Ramp Clearance Height.

Select an answer

How should a WCS orientation be set up when using soft jaws?

(Select one)

Z up.
X up.
Y up.
Z down.

Select an answer

If the machining preview region on a 2D Adaptive toolpath is incorrect relative to the selected geometry, how can it be changed?

(Select one)

Change the cutter compensation to In Control.
Delete and try the selection again.
Change from Climb to Conventional cut.
Click on the red arrow displayed on the side of cut during geometry selection.

Select an answer

Which of the following toolpaths would be a good option to finish a 3/8in counter-bore that has been predrilled with a .257in drill bit?

(Select one)

2D Pocket with a 1/4in ball endmill.
2D Contour with a 1/4in flat endmill.
Circular with a 1/4in chamfer mill.
Bore with a 3/8in flat endmill.

Select an answer

What is a limitation to creating a Setup Sheet from an NC Program for multiple setups?

(Select one)

The operations list will only display for a single setup.
The machining time will only be listed for a single setup.
The WCS Setup preview will be for a single setup.
The tools list will only display for a single setup.

Select an answer

What is a limiting factor that would prevent the use of a large shell mill to face a part?

(Select one)

Spindle RPM.
Spindle Horsepower.
Maximum Feedrate.
Depth of cut.

Select an answer

What kind of compensation should be set in Fusion for diameter wear adjustments to work?

(Select one)

Offset Compensation
Default Compensation
Tool Compensation
Wear Compensation

Select an answer

What tool would you use if you need to measure a depth with an accuracy of a few tenths of a thousandth?

(Select one)

Ruler
Depth Calipers
Depth Micrometer
Tape Measure

Select an answer

What should be done after completing a visual inspection of the part?

(Select one)

Discard the part and proceed to the next operation
Write the dimensions down on the inspection sheet
Record the dimensions in Fusion
Send the part to quality control

Select an answer

What happens when the geometry measures out of spec during probing?

(Select one)

The machine skips the next operation
The program can stop with a message on the machine
The machine automatically recalibrates
The operator is alerted, but the program continues

Select an answer

What does a “Model Aware Toolpath” mean?

(Select one)

The toolpath uses selected chains or contours to calculate machining movements.
The toolpath can machine flat areas as well as vertical walls.
The toolpath uses model geometry to calculate machining movements.
The toolpath can be used for rest machining.

Select an answer

Which linking parameter is used to control the size of the arc when exiting a cut?

(Select one)

Horizontal Lead-out Radius.
Linear Lead-in Distance
Horizontal Lead-in Radius.
Linear Lead-out Distance.

Select an answer

Which chamfer toolpath value can adjust the vertical position on the flute where geometry will be cut?

(Select one)

Chamfer Width.
Chamfer Tip Offset.
Finishing Overlap.
Chamfer Clearance.

Select an answer

What is likely to happen when simulating multiple setups at the same time that all include fixture definitions?

(Select one)

An increase in performance.
Inaccurate stock removal.
A decrease in performance.
False collisions.

Select an answer

What is the maximum allowable size for the piston bore with the tolerance applied?

(Select one)

1.068 inches
1.066 inches
1.067 inches
1.064 inches

Select an answer

Start your final test

Haas and Fusion 360 - Machined Part Finishing and Inspection final test

If a toolpath preview has a lot of rapid movements above the part, which toolpath setting is likely to reduce that?

How should a WCS orientation be set up when using soft jaws?

If the machining preview region on a 2D Adaptive toolpath is incorrect relative to the selected geometry, how can it be changed?

Which of the following toolpaths would be a good option to finish a 3/8in counter-bore that has been predrilled with a .257in drill bit?

What is a limitation to creating a Setup Sheet from an NC Program for multiple setups?

What is a limiting factor that would prevent the use of a large shell mill to face a part?

What kind of compensation should be set in Fusion for diameter wear adjustments to work?

What tool would you use if you need to measure a depth with an accuracy of a few tenths of a thousandth?

What should be done after completing a visual inspection of the part?

What happens when the geometry measures out of spec during probing?

What does a “Model Aware Toolpath” mean?

Which linking parameter is used to control the size of the arc when exiting a cut?

Which chamfer toolpath value can adjust the vertical position on the flute where geometry will be cut?

What is likely to happen when simulating multiple setups at the same time that all include fixture definitions?

What is the maximum allowable size for the piston bore with the tolerance applied?