Which type of view is used to show details hidden on features internal to a part?

(Select one)

Section.
Projected.
Detail.
Base.

Select an answer

Why is it important to consider datums and control frames on detailed drawings when planning to machine parts?

(Select one)

To plan the stock size before machining a part.
To determine the end use of a part.
To determine the order of operations for tolerance-controlled features.
To understand the quantity and post processing required.

Select an answer

When setting up an adaptive toolpath, which geometry option will ensure toolpaths aren’t created where there is no stock?

(Select one)

Stock Contours.
Contour Mode.
Wrap Toolpath.
Tool Orientation.

Select an answer

What is the correct way to center the stock in a vice?

(Select one)

Centered in the jaw
Off to one side
Balanced on top of the jaws
Clamped directly on the vice bed

Select an answer

Which type of view is used to show the ends of long parts while omitting the middle?

(Select one)

Projection.
Section.
Break.
Detail.

Select an answer

Which jaw of the vice should be used to indicate off while aligning the vice?

(Select one)

The movable jaw
The back fixed jaw
The front floating jaw
The middle jaw

Select an answer

What should be done before placing a vice on the mill table?

(Select one)

Use oil to lubricate the table.
Clean the table with a brush, T-slot cleaner, and wash-down hose.
Spray the table with coolant.
Polish the table with a high-speed buffing machine.

Select an answer

Which view type is used to create a larger scaled view of a specific area on another view?

(Select one)

Detail.
Base.
Projection.
Section.

Select an answer

What does it mean for a hole note on a detailed drawing to start with 4X?

(Select one)

This is the 4th revision of the feature.
There are 4 of the same feature on the part.
The scale of the view is 4:1.
The scale of the view is 1:4.

Select an answer

What is another common term for a parts lists found on detailed drawings?

(Select one)

Balloon Table.
Material List.
Bend Table.
Bill of Materials.

Select an answer

Which Fusion 360 drawing standard uses a 1st Angle Projection?

(Select one)

BS.
ISO.
ASME.
JIS.

Select an answer

What term refers to the amount a tool sticks out of its holder in the Fusion 360 tool library?

(Select one)

Shoulder length.
Overall length.
Flute length.
Length below holder.

Select an answer

What is the upper and lower limits of a dimension listed as 3 ±.002 ?

(Select one)

2.998 – 3.002.
3.000 – 3.000.
2.998 – 3.000.
3.000 – 3.002.

Select an answer

What should you avoid when setting tool offsets in a CNC machine setup?

(Select one)

Adjusting tool offsets directly from the setup sheet
Setting the Z offset to zero manually
Mixing manual and probing methods for setting tool offsets
Using ER-style holders for different tool sizes

Select an answer

What is the main purpose of performing a dry run in graphics mode before cutting actual material?

(Select one)

To verify the tool path and detect potential errors without risking a collision.
To test the machine’s coolant system.
To increase the cutting speed of the tool.
To ensure the material is securely clamped.

Select an answer

Start your final test

Haas and Fusion 360 - Blueprints, CAD, CAM, and CNC final test

Which type of view is used to show details hidden on features internal to a part?

Why is it important to consider datums and control frames on detailed drawings when planning to machine parts?

When setting up an adaptive toolpath, which geometry option will ensure toolpaths aren’t created where there is no stock?

What is the correct way to center the stock in a vice?

Which type of view is used to show the ends of long parts while omitting the middle?

Which jaw of the vice should be used to indicate off while aligning the vice?

What should be done before placing a vice on the mill table?

Which view type is used to create a larger scaled view of a specific area on another view?

What does it mean for a hole note on a detailed drawing to start with 4X?

What is another common term for a parts lists found on detailed drawings?

Which Fusion 360 drawing standard uses a 1st Angle Projection?

What term refers to the amount a tool sticks out of its holder in the Fusion 360 tool library?

What is the upper and lower limits of a dimension listed as 3 ±.002 ?

What should you avoid when setting tool offsets in a CNC machine setup?

What is the main purpose of performing a dry run in graphics mode before cutting actual material?