Which statement best describes the drilling cycle Rapid Out?

(Select one)

The tool uses a consistent pecking motion with micro rapid movements to evacuate chips while drilling.
The tool engages the material at the specified federate and retracts at a rapid feedrate.
The tool engages the material a small peck at a time, dwells for a period of time and rapids out to the feed plane before proceeding.
The tool engages the material a small peck at a time and rapids out to the feed plane before proceeding.

Select an answer

What should you do before running the first tool in operation for the first time?

(Select one)

Lower the machine temperature
Press feed hold and verify distance to go and program positions
Skip the feed hold process if the part looks good
Increase feed rates to 100% immediately

Select an answer

What is the difference between a Fusion .F3Z file and a . F3D file?

(Select one)

A .F3D file contains only 3D designs while a .F3Z file contains toolpath data.
A .F3D file is 2D while a .F3Z file is 3D.
A .F3Z file contains multiple externally linked designs.
A .F3D file contains multiple externally linked designs.

Select an answer

When creating a 2D Pocket toolpath what will happen to the cutting depth if multiple faces are selected at multiple depths?

(Select one)

Each face will be machined at its selected height.
All faces will be machined at the shallowest faces depth.
The toolpath will fail and require an individual selection.
All faces will be machined at the deepest faces depth.

Select an answer

If a hole is oversized during inspection, what should you check first?

(Select one)

Check the tool used to create the hole, like the drill bit
Increase the RPM of the machine
Check the coolant concentration
Rerun the program without making changes

Select an answer

Which modify tool can be used to great a tapered edge typically used to debur a part?

(Select one)

Offset Face.
Press Pull.
Chamfer.
Fillet.

Select an answer

If the corner of a model is sharp and a 2D chamfer toolpath is used, how is that displayed during a stock comparison simulation?

(Select one)

It is displayed as a collision.
It is displayed as material left behind.
It is not displayed since it was not part of the original model.
It is displayed as transparent.

Select an answer

What is an aligned dimension creating a 2D sketch and applying a dimension between 2 points?

(Select one)

A dimension that is aligned parallel to the Y-axis.
A dimension that will provide the maximum distance between the 2 selected points.
A dimension that is aligned parallel to the X-axis.
A dimension that will provide the minimum distance between the 2 selected points.

Select an answer

Where can information about the mass of a part be found?

(Select one)

Selection tool.
Body properties dialog.
Modify Parameters dialog.
Measure tool.

Select an answer

Why is it important to verify coolant levels and concentration before running a part?

(Select one)

It increases the machine's torque
It helps flush chips away and prevents tools from overheating
It prevents rusting of the machine
It slows down the machine's RPM

Select an answer

Which display option can help identify if a tool has enough cutting flute to reach all geometry on a part?

(Select one)

Show tool.
Show toolpath.
Show tool on cursor.
Show in-process stock.

Select an answer

What is the purpose of running the program in graphics mode before starting the operation?

(Select one)

To see where the tools should be starting and detect alarms
To measure the part automatically
To adjust the machine speed
To adjust the tool wear

Select an answer

What tool is recommended to measure a 0.6-inch step during inspection?

(Select one)

Tape measure
Steel ruler
Calipers
Digital depth micrometer

Select an answer

Which toolpath options can control how much time a tool spends above the part before cutting material?

(Select one)

Geometry.
Heights.
Linking parameters.
Passes.

Select an answer

What does it mean for a tool library name to be displayed in grey?

(Select one)

The library is not currently used in any document.
The library is out-of-date.
The library is not enabled and loaded.
The library contains new tools.

Select an answer

Start your final test

Haas and Fusion 360 - CAD, CAM, and Part Programming final test

Which statement best describes the drilling cycle Rapid Out?

What should you do before running the first tool in operation for the first time?

What is the difference between a Fusion .F3Z file and a . F3D file?

When creating a 2D Pocket toolpath what will happen to the cutting depth if multiple faces are selected at multiple depths?

If a hole is oversized during inspection, what should you check first?

Which modify tool can be used to great a tapered edge typically used to debur a part?

If the corner of a model is sharp and a 2D chamfer toolpath is used, how is that displayed during a stock comparison simulation?

What is an aligned dimension creating a 2D sketch and applying a dimension between 2 points?

Where can information about the mass of a part be found?

Why is it important to verify coolant levels and concentration before running a part?

Which display option can help identify if a tool has enough cutting flute to reach all geometry on a part?

What is the purpose of running the program in graphics mode before starting the operation?

What tool is recommended to measure a 0.6-inch step during inspection?

Which toolpath options can control how much time a tool spends above the part before cutting material?

What does it mean for a tool library name to be displayed in grey?