Which 2D toolpath is effective for finishing floors and walls of both open and closed geometry?

(Select one)

Pocket.
Trace.
Adaptive Clearing.
Contour.

Select an answer

How can tolerance be added to a dimension in a Fusion 360 drawing?

(Select one)

From the dimension toolbar drop-down select Ordinate Dimension.
Double-click on the dimension and enable the tolerance option in the dimension dialog.
During dimension creation hold down the ALT key.
Edit the Sheet Settings and activate tolerances.

Select an answer

Why is it important to set a unique work coordinate system (WCS) for each part in a multi-part setup?

(Select one)

To ensure each part has its own precise reference, avoiding overlap with other parts.
To avoid using CAM software for changes.
To allow all parts to share the same machining code.
To prevent the need for multiple vices.

Select an answer

What is the purpose of setting up G55 instead of G54 in this video?

(Select one)

To use fewer offsets overall.
To enable automatic tool changes.
To speed up the machining process.
To assign a unique work coordinate system for the second operation.

Select an answer

Which view type will allow you to cut a model using a straight line revealing internal geometry?

(Select one)

Section.
Auxiliary .
Detail.
Break.

Select an answer

Which drawing creation dialog setting will control if a drawing is 1st Angle or 3rd Angle projection?

(Select one)

Standard.
Contents.
Units.
Drawing.

Select an answer

How can a joint limit be set up to always return to a specific location?

(Select one)

Enable a Rest position.
Reduce the minimum joint limit value.
Create a Tangent Relationship.
Enable Contact Sets.

Select an answer

What notes should be left in the jaw program?

(Select one)

The size of the jaws and spacer needed
The color of the jaws
The weight of the jaws
The brand of the jaws

Select an answer

What G code is used for the second operation?

(Select one)

G50
G56
G54
G55

Select an answer

Which WCS Origin point type is used if you want to select the corner of CAD geometry?

(Select one)

Model box point.
Stock box point.
Model origin.
Selected point.

Select an answer

Which sketch tool will create sketch lines that match where a solid body hits the construction plane for the sketch?

(Select one)

Project.
Project to Surface.
Include 3D Geometry.
Intersect.

Select an answer

Which inspection tool can check if any parts of an assembly overlap and calculate the volume of overlap?

(Select one)

Measure.
Interference.
Isocurve Analysis.
Accessibility Analysis.

Select an answer

How can a Setup Sheet be adjusted to only show a tool list?

(Select one)

Right-click on the NC Program and select Configure Output.
Toggle the post tool list option inside of the post properties.
Right-click on the NC Program and select Tool List.
Change the setup sheet configuration drop down to Tool List.

Select an answer

Where can the option be toggled on to enable a chip transport to run during a program?

(Select one)

Post configurator.
Post properties.
CAM setup.
Output folder.

Select an answer

What is the significance of the plus or minus signs for G 55 Z value?

(Select one)

They indicate tool brand
They denote direction
They show material type
They are optional

Select an answer

Start your final test

Haas and Fusion 360 - Drafting, Soft Jaw Design, and Programming

Which 2D toolpath is effective for finishing floors and walls of both open and closed geometry?

How can tolerance be added to a dimension in a Fusion 360 drawing?

Why is it important to set a unique work coordinate system (WCS) for each part in a multi-part setup?

What is the purpose of setting up G55 instead of G54 in this video?

Which view type will allow you to cut a model using a straight line revealing internal geometry?

Which drawing creation dialog setting will control if a drawing is 1st Angle or 3rd Angle projection?

How can a joint limit be set up to always return to a specific location?

What notes should be left in the jaw program?

What G code is used for the second operation?

Which WCS Origin point type is used if you want to select the corner of CAD geometry?

Which sketch tool will create sketch lines that match where a solid body hits the construction plane for the sketch?

Which inspection tool can check if any parts of an assembly overlap and calculate the volume of overlap?

How can a Setup Sheet be adjusted to only show a tool list?

Where can the option be toggled on to enable a chip transport to run during a program?

What is the significance of the plus or minus signs for G 55 Z value?